Installing A Bath tub
Installing A Bath tub
Blog Article
How do you actually feel on the subject of How to Install a Bathtub Yourself?
Mounting a bathtub isn't precisely brain surgery, however it does need solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old tub with a new one is likewise a moderately challenging project. If the old bathtub is readily obtainable, the job can relocate immediately; if you need to open a wall surface to eliminate the old tub as well as position the brand-new tub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Make certain you have actually qualified yourself for the task and fit trying it. Rather than employing a service provider to take control of a halfway-completed job, it is far better to consider using one before you begin. Opportunities are you may require a specialist plumber to make tube links.
This short article will certainly aid you install a new bath tub in your restroom if you have actually already gotten a brand-new bathtub and do not require to change the arrangement of your previous water system pipelines.
Your tools as well as product checklist must consist of the following:
Preparing for the Installation
First of all, the sustaining frame supplied with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of both faucets using 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its last placement.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The process of getting rid of the existing faucets can be fairly troublesome due to the limited accessibility that is usually the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny factors.
The next goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bath tub up until the spirit level checks out level.
To set up taps, fit all-time low of the furthest versatile tap port to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Activate the water system and also inspect all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as also examine the overflow outlet and the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the bath tub ought to wait up until the bath tub has been made use of at the very least when as this will certainly settle it into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin ensuring that the washers remain in location in between the faucet and the sink. Secure the faucet in position with the supplier provided backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous kind should be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break an inflexible seal, creating the water to penetrate the wall surface between the bathroom and the tiling, leading to issues with moisture and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also fittings. They are marketed in tubes and cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to securing, to enable the activity experienced when the bathtub remains in use. The sealer can break fairly very early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water resistant sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our topic on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for spending some time to browse our content. Do you know somebody else who is very much interested in the topic? Please feel free to share it. Thank you for your time. Visit us again soon.
Get Your Estimate Now
Report this page